Environmental risks from consumer products: Acceptable drinking water quality can produce unacceptable indoor air quality with ultrasonic humidifier use.

The commonly used consumer product of an ultrasonic humidifier (e.g., cool mist humidifier) emits fine particles containing metals from tap water used to fill the humidifier. The objectives are: 1) predict emitted indoor air inhalable metal concentrations produced by an ultrasonic humidifier filled with tap-water containing As, Cd, Cr, Cu, Mn, and Pb in 33 m3 or 72 m3 rooms with varying air exchange rates; 2) calculate daily ingestion and 8-h inhalation average daily dose (ADD) and hazard quotient (HQ) for adults and children (aged 0.25-6 yr); and 3) quantify deposition in respiratory tract via multi-path particle dosimetry (MPPD) model. Mass concentrations of indoor air metals increase proportionally with aqueous metal concentrations in fill water, and are inversely related to ventilation. Inhalation-ADDs are 2 magnitudes lower than ingestion-ADDs, using identical water quality for ingestion and fill-water. However, in the 33 m3, low 0.2/h ventilated room, inhalation-HQs are >1 for children and adults, except for Pb. HQ inhalation risks exceed ingestion risks at drinking water regulated levels for As, Cd, Cr, and Mn. MPPD shows greater dose deposits in lungs of children than adults, and 3 times greater deposited doses in a 33 m3 vs 72 m3 room. Rethinking health effects of drinking water and consumer products to broaden consideration of multiple exposure routes is needed.

Exposure at the indoor water-air interface: Fill water constituents and the consequent air emissions from ultrasonic humidifiers: A systematic review.

This systematic review investigates the emissions from ultrasonic humidifiers (e.g., cool mist humidifiers) within indoor air environments, namely soluble and insoluble metals and minerals as well as microorganisms and one organic chemical biocide. Relationships between ultrasonic humidifier fill water quality and the emissions in indoor air are studied, and associated potential adverse health outcomes are discussed. Literature from January 1, 1980, to February 1, 2022, was searched from online databases of PubMed, Web of Science, and Scopus to produce 27 articles. The results revealed clear positive proportional relationships of the concentration of microorganisms and soluble metals/minerals between fill water qualities and emitted airborne particles, for both microbial (n = 9) and inorganic (n = 15) constituents. When evaluating emissions and the consequent health outcomes, ventilation rates of specific exposure scenarios affect the concentrations of emitted particles. Thus, well-ventilated rooms may alleviate inhalation risks when the fill water in ultrasonic humidifiers contains microorganisms and soluble metals/minerals. Case reports (n = 3) possibly due to the inhalation of particles from ultrasonic humidifier include hypersensitivity pneumonitis in adults and a 6-month infant; the young infant exhibited nonreversible mild obstructive ventilator defect. In summary, related literature indicated correlation between fill water quality of ultrasonic humidifier and emitted particles in air quality, and inhalation of the emitted particles may cause undesirable health outcomes of impaired respiratory functions in adults and children.

Data Analytics Determines Co-occurrence of Odorants in Raw Water and Evaluates Drinking Water Treatment Removal Strategies.

A complex dataset with 140 sampling events was generated using triple quadrupole gas chromatography-mass spectrometer to track the occurrence of 95 odorants in raw and finished water from 98 drinking water treatment plants in 31 cities across China. Data analysis identified more than 70 odorants with concentrations ranging from not detected to thousands of ng/L. In raw water, Pearson correlation analysis determined that thioethers, non-oxygen benzene-containing compounds, and pyrazines were classes of chemicals that co-occurred, and geosmin and p(m)-cresol, as well as cyclohexanone and benzaldehyde, also co-occurred, indicating similar natural or industrial sources. Based on classification and regression tree analysis, total dissolved organic carbon and geographical location were identified as major factors affecting the occurrence of thioethers. Indoles, phenols, and thioethers were well-removed through conventional and advanced treatment processes, while some aldehydes could be generated. For other odorants, higher removal was achieved by ozonation-biological activated carbon (39.3%) compared to the conventional treatment process (14.5%). To our knowledge, this is the first study to systematically identify the major odorants in raw water and determine suitable treatment strategies to control their occurrence by applying data analytics and statistical methods to the complex dataset. These provide informative reference for odor control and water quality management in drinking water industry.

Risks to children from inhalation of aerosolized aqueous manganese emitted from ultrasonic humidifiers can be greater than for corresponding ingestion.

The essential trace element manganese (Mn) can cause neurotoxicity with inhalation acknowledged as a more severe health and cognition threat than ingestion. METHODS: Over a range of aqueous Mn concentrations present in tap water, this research characterizes exposures and risks for adults and 0.25, 1, 2.5, and 6 yr old children who ingest the water and inhale respirable particles produced by a room-sized ultrasonic humidifier filled with the same water. Aqueous Mn concentrations evaluated included 50 µg/L USEPA esthetic guideline, 80 µg/L WHO infant guideline, and 120 µg/L Canadian regulatory level. Airborne-particle-bound Mn concentrations were generated for water filling an ultrasonic humidifier under four realistic room conditions (33 m3 small or 72 m3 large) with varying ventilation rates from 0.2/h -1.5/h. Average daily doses (ADD) and reference intake doses were calculated for ingestion and 8-h inhalation of humidified air. Hazard quotients (HQ) compared the intake doses and reference doses. Multi-path particle dosimetry (MPPD) model quantified the particle deposition and deposited dose in children's and adults' respiratory tracts. RESULTS: At only 11 µg/L Mn, the resulting humidified air Mn exceeds USEPA's reference concentration of 0.05 µg/m3 Mn in small room with low, energy-efficient ventilation. Inhalation ADD are 2 magnitudes lower than ingestion ADD for identical water Mn concentrations and daily exposure frequency. Even so, ingestion HQs are approximately 0.2 but inhalation risk is significant (HQ>1) for children and adults when breathing Mn-humidified air under most small room conditions at 50, 80 or 120 µg/L Mn. MPPD model indicates inhaled Mn deposits in head and pulmonary regions, with greater Mn dose deposits in children than adults. CONCLUSION: Inhalation of Mn-particles produced from ultrasonic humidifiers can pose greater risks than ingestion at the same water concentration, especially for children. Aqueous Mn concentration and room size influence risks. Limiting manganese exposures and setting regulations requires consideration of both ingestion and inhalation of water.

Children and adults are exposed to dual risks from ingestion of water and inhalation of ultrasonic humidifier particles from Pb-containing water.

Room-sized ultrasonic humidifiers are exposure pathways to aerosolized metals, with dose positively associated with increased concentrations of metals in fill water. This study innovatively quantifies water ingestion along with inhalation doses from humidifiers for 10-1000 µg/L dissolved lead (Pb) in tap water. The subsequent indoor air Pb concentrations, average daily doses, and inhalation deposited respiratory fractions were predicted under four room scenarios for 3-mo, 12-mo, 28-mo, and 6-yr children and adults. Elevated blood Pb levels (BLLs) in children were modeled using USEPA's Integrated Exposure Uptake Biokinetic (IEUBK) model. Indoor air Pb exceeds the USEPA ambient air standard of 0.15 µg/m3 when humidifier fill water contains 33 µg/L Pb in the small room of 33.5 m3 and 0.2 h-1 air exchange rate (AER). For this room, ~40-46% inhaled Pb-containing humidifier particles deposit in children's respiratory tracts; inhaling humidifier particles from ≥500 µg/L Pb water results in >1 µg/dL BLL in 2-7 yr children. For adults, ~23% of particles deposit in the respiratory tract; 8-h inhalation exposure with ≥17 µg/L Pb water exceeds the California EPA reproductive toxicity guideline of 0.5 µg/day. Larger rooms and higher AER decrease Pb inhalation exposure under the same water Pb concentration.

An overlooked route of inhalation exposure to tap water constituents for children and adults: Aerosolized aqueous minerals from ultrasonic humidifiers.

Fine particulates and aerosols emitted by commonly used, room-sized ultrasonic humidifiers may pose adverse health effects to children and adults. The literature documents adverse effects for children exposed to minerals emitted from humidifiers. This study performs novel and comprehensive characterization of bivariate particle size and element concentrations of emitted airborne aerosols and particles from ultrasonic humidifiers filled with tap water, including size distribution from 0.014 to 10 µm by scanning mobility particle sizer and AeroTrak; corresponding metal and elemental concentrations as a function of particle size by inductively coupled plasma mass spectrometer; and calculations of deposition fraction in human lungs for age-specific groups using the multi-path particle dosimetry model (MPPD). Deposition fraction is the ratio of mass deposited to total mass inhaled. When filled with tap water, water evaporated from emitted aerosols to form submicron particles that became essentially "dried tap water" with median size 146 nm and mean concentration of 211 µg-total elements/m3-air including 35 µg-calcium/m3-air in a room of 33.5 m3 and air exchange rate at ∼0.8 hr-1. Approximately 90% of emitted particles deposited in human lungs were <1 µm as shown by MPPD model. The smaller particles contained little water and higher concentration of minerals, while larger particles of >1 µm consisted of lower elemental concentrations and more water due to low evaporation. Deposition fraction in pulmonary region was ∼2-fold higher, and deposited particulate mass was 3.5-fold higher for children than adults, indicating greater inhalation exposure to children compared to adults. Modeled data of total particles mass per body weight (BW) that will deposit in adult and child lungs after 8-h humidifier exposure were respectively 2.8 µg/kg-BW and 9.8 µg/kg-BW, where calcium contributes 0.4 µg/kg-BW and 1.6 µg/kg-BW. This comprehensive study of bivariate inorganic chemical composition as a function of particle size expanded, quantified, and modeled exposure for children and adults to aerosolized calcium and other inorganic constituents in water.

Human exposure to particles at the air-water interface: Influence of water quality on indoor air quality from use of ultrasonic humidifiers.

Ultrasonic humidifiers provide indoor relief to symptoms caused by dry air and produce aerosols containing both water and minerals that are present in the water that fills the humidifier. This study investigated the spatial distributions, concentrations, and metal and mineral composition of aerosols emitted when an ultrasonic humidifier was filled with deionized water (DI), low mineral tap water (LL), high total dissolved solids (TDS)/high hardness water (HH), and high TDS/low hardness water (HL). Aerosol/particle sizes and counts were obtained at six horizontal distances in both the plume and near floor for each water quality. Results are that water quality significantly affects particle size distributions which become uniform after 0.9 m from the humidifier outlet, and are independent of vertical distance from the humidifier. The mean count median diameters were 64 nm for DI, 129 nm for LL, 234 nm for HH, and 260 nm for HL; the particle counts and total mineral solids concentrations were 2,194 #/cm3 (16 µg/m3) for DI, 21,070 #/cm3 (113 µg/m3) for LL, 38,353 #/cm3 (438 µg/m3) for HH, and 43,880 #/cm3 (521 µg/m3) for HL. The µg/m3 values for LL, HH, and HL exceeded PM2.5 ambient air standards. Model predictions are that the deposition mass in the human respiratory system from inhaling particles emitted from HH and HL water exceed 135 µg for a 1 to 3-month old child and 600 µg for an adult over an 8-hr period. Mineral water quality significantly affects the distribution and concentration of emitted and inhaled indoor air particles. Consumers may unknowingly be degrading their indoor air quality when using tap water of acceptable drinking water quality as humidifier fill water.

The Facial Action Coding System for Characterization of Human Affective Response to Consumer Product-Based Stimuli: A Systematic Review.

To characterize human emotions, researchers have increasingly utilized Automatic Facial Expression Analysis (AFEA), which automates the Facial Action Coding System (FACS) and translates the facial muscular positioning into the basic universal emotions. There is broad interest in the application of FACS for assessing consumer expressions as an indication of emotions to consumer product-stimuli. However, the translation of FACS to characterization of emotions is elusive in the literature. The aim of this systematic review is to give an overview of how FACS has been used to investigate human emotional behavior to consumer product-based stimuli. The search was limited to studies published in English after 1978, conducted on humans, using FACS or its action units to investigate affect, where emotional response is elicited by consumer product-based stimuli evoking at least one of the five senses. The search resulted in an initial total of 1,935 records, of which 55 studies were extracted and categorized based on the outcomes of interest including (i) method of FACS implementation; (ii) purpose of study; (iii) consumer product-based stimuli used; and (iv) measures of affect validation. Most studies implemented FACS manually (73%) to develop products and/or software (20%) and used consumer product-based stimuli that had known and/or defined capacity to evoke a particular affective response, such as films and/or movie clips (20%); minimal attention was paid to consumer products with low levels of emotional competence or with unknown affective impact. The vast majority of studies (53%) did not validate FACS-determined affect and, of the validation measures that were used, most tended to be discontinuous in nature and only captured affect as it holistically related to an experience. This review illuminated some inconsistencies in how FACS is carried out as well as how emotional response is inferred from facial muscle activation. This may prompt researchers to consider measuring the total consumer experience by employing a variety of methodologies in addition to FACS and its emotion-based interpretation guide. Such strategies may better conceptualize consumers' experience with products of low, unknown, and/or undefined capacity to evoke an affective response such as product prototypes, line extensions, etc.

Pyrazines: A diverse class of earthy-musty odorants impacting drinking water quality and consumer satisfaction.

The presence of earthy-musty odors in drinking water is a major concern for water suppliers and consumers worldwide. While geosmin and 2-methylisoborneol are the most studied earthy-musty odor-causing compounds, pyrazine and its alkyl and methoxy compounds possess similar odors and are widely distributed in nature, foods, and beverages. In this study, odor characteristics of pyrazines and their presence in natural and treated waters were determined. Pyrazine, 2,6-dimethyl-pyrazine (DMP), 2,3,5-trimethyl-pyrazine (TrMP), 2-ethyl-5(6)-methyl-pyrazine (EMP), 2,3,5,6-tetramethyl-pyrazine (TeMP), 2-isobutyl-3-methoxy-pyrazine (IBMP) and 2-isopropyl-3-methoxy-pyrazine (IPMP) were measured in source and finished drinking water across China. 2-Methoxy-3,5-dimethyl-pyrazine (MDMP), IBMP, and IPMP were investigated in rivers in Virginia, USA. The results showed that "musty" and "sweet" were the most common descriptors for pyrazine, DMP, MDMP, TrMP, and TeMP. While IBMP and IPMP were never detected in 140 source or drinking water samples from across China, pyrazine, DMP, MDMP, TrMP, and TeMP occurred throughout with concentrations of n.d.-62.2 ng/L-aq in source water and n.d.-39.6 ng/L-aq in finished water. IBMP, IPMP, and MDMP were present in two Virginia rivers; MDMP occurred in 18% of the samples with concentrations of n.d.-4.4 ng/L, many of which were above the aqueous odor threshold of 0.043 ng/L MDMP. The removal efficiencies through conventional water treatment were poor, ranging from negative removals to ∼10%. Advanced oxidation water treatment could only remove EMP and TrMP. The widespread presence of earthy-musty-sweet pyrazines in source and drinking waters on two continents, their poor removal during water treatment, and ng/L odor threshold concentrations confirm their potential to be T&O issues for consumers.

Emission of iron and aluminum oxide particles from ultrasonic humidifiers and potential for inhalation.

Ultrasonic humidifier use is a potential source of human exposure to inhalable particulates. This research evaluated the behavior of insoluble iron oxide and aluminum oxide particles in water used to fill room-sized ultrasonic humidifiers. Solutions of 10 mg/L Fe, as iron oxide particles, or 5 mg/L Al, as aluminum oxide suspension, were added into tap water used to fill ultrasonic humidifiers. The humidifiers were operated for 14 h; samples were obtained over time and monitored for soluble and particulate Fe and Al, as well as particle sizes in the humidifier reservoir and emitted in aerosols. Denser, settleable particles of approximately 1.5 µm diameter of iron or aluminum oxides accumulated at the bottom of the humidifier reservoir. Smaller, suspended metal oxide particles of 0.22-0.57 µm diameter were emitted as aerosols from the humidifier. Soluble anions and cations in tap water were also present in the aerosols emitted from humidifiers. The results indicate that a typical 1.6 MHz ultrasonic humidifier can emit 0.22-0.57 µm particles and dissolved minerals from fill water into breathable air.

Potential for city parks to reduce exposure to BTEX in air.

Benzene, toluene, ethylbenzene, and xylenes (BTEX) are hazardous air pollutants commonly found in outdoor air. Several studies have explored the potential of vegetation to mitigate BTEX in outdoor air, but they are limited to a northern temperate climate and their results lack consensus. To investigate this subject in a subtropical climate, we deployed passive air samplers for two weeks in parks and outside nearby residences at four locations: three in an urban area and one in a rural area in Alabama, USA. All BTEX concentrations were below health-based guidelines and were comparable to those found in several other studies in populated settings. Concentrations of TEX, but not benzene, were 3-39% lower in parks than at nearby residences, and the differences were significant. Site type (park vs. residential) was a significant predictor of TEX concentrations, while distance to the nearest major road was a significant predictor of BTX concentrations. In and around two of the parks, toluene : benzene ratios fell outside the range expected for vehicular emissions (p < 0.01), suggesting that there were additional, industrial sources of benzene near these two locations. The ratio of m-,p-xylene : ethylbenzene was high at all locations except one residential area, indicating that BTEX were freshly emitted. Concentrations of individual BTEX compounds were highly correlated with each other in most cases, except for locations that may have been impacted by nearby industrial sources of benzene. Results of this study suggest that parks can help reduce exposure to TEX by a modest amount in some situations.

Survival of the Enveloped Virus Phi6 in Droplets as a Function of Relative Humidity, Absolute Humidity, and Temperature.

Infectious diseases caused by enveloped viruses, such as influenza, severe acute respiratory syndrome (SARS), and Middle East respiratory syndrome (MERS), cause thousands of deaths and billions of dollars of economic losses per year. Studies have found a relationship among temperature, humidity, and influenza virus incidence, transmission, or survival; however, there are contradictory claims about whether absolute humidity (AH) or relative humidity (RH) is most important in mediating virus infectivity. Using the enveloped bacteriophage Phi6, which has been suggested as a surrogate for influenza viruses and coronaviruses, we designed a study to discern whether AH, RH, or temperature is a better predictor of virus survival in droplets. Our results show that Phi6 survived best at high (>85%) and low (<60%) RHs, with a significant decrease in infectivity at mid-range RHs (∼60 to 85%). At an AH of less than 22 g · m-3, the loss in infectivity was less than 2 orders of magnitude; however, when the AH was greater than 22 g · m-3, the loss in infectivity was typically greater than 6 orders of magnitude. At a fixed RH of 75%, infectivity was very sensitive to temperature, decreasing two orders of magnitude between 19°C and 25°C. We used random forest modeling to identify the best environmental predictors for modulating virus infectivity. The model explained 83% of variation in Phi6 infectivity and suggested that RH is the most important factor in controlling virus infectivity in droplets. This research provides novel information about the complex interplay between temperature, humidity, and the survival of viruses in droplets.IMPORTANCE Enveloped viruses are responsible for a number of infectious diseases resulting in thousands of deaths and billions of dollars of economic losses per year in the United States. There has been a lively debate in the literature over whether absolute humidity (AH) or relative humidity (RH) modulates virus infectivity. We designed a controlled study and used advanced statistical modeling techniques specifically to address this question. By providing an improved understanding of the relationship between environmental conditions and virus infectivity, our work will ultimately lead to improved strategies for predicting and controlling disease transmission.

Food Safety Practices Linked with Proper Refrigerator Temperatures in Retail Delis.

Listeria monocytogenes (L. monocytogenes) causes the third highest number of foodborne illness deaths annually. L. monocytogenes contamination of sliced deli meats at the retail level is a significant contributing factor to L. monocytogenes illness. The Centers for Disease Control and Prevention's Environmental Health Specialists Network (EHS-Net) conducted a study to learn more about retail delis' practices concerning L. monocytogenes growth and cross-contamination prevention. This article presents data from this study on the frequency with which retail deli refrigerator temperatures exceed 41°F, the Food and Drug Administration (FDA)-recommended maximum temperature for ready-to-eat food requiring time and temperature control for safety (TCS) (such as retail deli meat). This provision was designed to control bacterial growth in TCS foods. This article also presents data on deli and staff characteristics related to the frequency with which retail delis refrigerator temperatures exceed 41°F. Data from observations of 445 refrigerators in 245 delis showed that in 17.1% of delis, at least one refrigerator was >41°F. We also found that refrigeration temperatures reported in this study were lower than those reported in a related 2007 study. Delis with more than one refrigerator, that lacked refrigerator temperature recording, and had a manager who had never been food safety certified had greater odds of having a refrigerator temperature >41°F. The data from this study suggest that retail temperature control is improving over time. They also identify a food safety gap: some delis have refrigerator temperatures that exceed 41°F. We also found that two food safety interventions were related to better refrigerated storage practices: kitchen manager certification and recording refrigerated storage temperatures. Regulatory food safety programs and the retail industry may wish to consider encouraging or requiring kitchen manager certification and recording refrigerated storage temperatures.

Protocol for Data Collection and Analysis Applied to Automated Facial Expression Analysis Technology and Temporal Analysis for Sensory Evaluation.

We demonstrate a method for capturing emotional response to beverages and liquefied foods in a sensory evaluation laboratory using automated facial expression analysis (AFEA) software. Additionally, we demonstrate a method for extracting relevant emotional data output and plotting the emotional response of a population over a specified time frame. By time pairing each participant's treatment response to a control stimulus (baseline), the overall emotional response over time and across multiple participants can be quantified. AFEA is a prospective analytical tool for assessing unbiased response to food and beverages. At present, most research has mainly focused on beverages. Methodologies and analyses have not yet been standardized for the application of AFEA to beverages and foods; however, a consistent standard methodology is needed. Optimizing video capture procedures and resulting video quality aids in a successful collection of emotional response to foods. Furthermore, the methodology of data analysis is novel for extracting the pertinent data relevant to the emotional response. The combinations of video capture optimization and data analysis will aid in standardizing the protocol for automated facial expression analysis and interpretation of emotional response data.

Subtleties of human exposure and response to chemical mixtures from spills.

Worldwide, chemical spills degrade drinking water quality and threaten human health through ingestion and inhalation. Spills are often mixtures of chemicals; thus, understanding the interaction of chemical and biological properties of the major and minor components is critical to assessing human exposure. The crude (4-methylcyclohexyl)methanol (MCHM) spill provides an opportunity to assess such subtleties. This research determined the relative amounts, volatilization, and biological odor properties of minor components cis- and trans-methyl-4-methylcyclohexanecarboxylate (MMCHC) isomers and major components cis- and trans-4-MCHM, then compared properties and human exposure differences among them. (1)H nuclear magnetic resonance and chromatography revealed that the minor MMCHC isomers were about 1% of the major MCHM isomers. At typical showering temperature of 40 °C, Henry's law constants were 1.50 × 10(-2) and 2.23 × 10(-2) for cis- and trans-MMCHC, respectively, which is 20-50 fold higher than for 4-MCHM isomers. The odor thresholds were 1.83 and 0.02 ppb-v air for cis- and trans-MMCHC, which were both described as predominantly sweet. These data are compared to the higher 120 ppb-v air and 0.06 ppb-v odor thresholds for cis- and trans-4-MCHM, for which the trans-isomer had a dominant licorice descriptor. Application of a shower model demonstrated that while MMCHC isomers are only about 1% of the MCHM isomers, during showering, the MMCHC isomers are 13.8% by volume (16.3% by mass) because of their higher volatility. Trans-4-MCHM contributed about 82% of the odor because of higher volatility and lower odor threshold, trans-MMCHC, which represents 0.3% of the mass, contributed 18% of the odor. This study, with its unique human sensory component to assess exposure, reaffirmed that hazard assessment must not be based solely on relative concentration, but also consider the chemical fate, transport, and biological properties to determine the actual levels of exposure across different media.

Incidence of waterborne lead in private drinking water systems in Virginia.

Although recent studies suggest contamination by bacteria and nitrate in private drinking water systems is of increasing concern, data describing contaminants associated with the corrosion of onsite plumbing are scarce. This study reports on the analysis of 2,146 samples submitted by private system homeowners. Almost 20% of first draw samples submitted contained lead concentrations above the United States Environmental Protection Agency action level of 15 µg/L, suggesting that corrosion may be a significant public health problem. Correlations between lead, copper, and zinc suggested brass components as a likely lead source, and dug/bored wells had significantly higher lead concentrations as compared to drilled wells. A random subset of samples selected to quantify particulate lead indicated that, on average, 47% of lead in the first draws was in the particulate form, although the occurrence was highly variable. While flushing the tap reduced lead below 15 µg/L for most systems, some systems experienced an increase, perhaps attributable to particulate lead or lead-bearing components upstream of the faucet (e.g., valves, pumps). Results suggest that without including a focus on private as well as municipal systems it will be very difficult to meet the existing national public health goal to eliminate elevated blood lead levels in children.

Assessing human exposure and odor detection during showering with crude 4-(methylcyclohexyl)methanol (MCHM) contaminated drinking water.

In 2014, crude (4-methylcyclohexyl)methanol (MCHM) spilled, contaminating the drinking water of 300,000 West Virginians and requiring "do not use" orders to protect human health. When the spill occurred, known crude MCHM physicochemical properties were insufficient to predict human inhalation and ingestion exposures. Objectives are (1) determine Henry's Law Constants (HLCs) for 4-MCHM isomers at 7, 25, 40, and 80°C using gas chromatography; (2) predict air concentrations of 4-MCHM and methyl-4-methylcyclohexanecarboxylate (MMCHC) during showering using an established shower model; (3) estimate human ingestion and inhalation exposure to 4-MCHM and MMCHC; and (4) determine if predicted air 4-MCHM exceeded odor threshold concentrations. Dimensionless HLCs of crude cis- and trans-4-MCHM were measured to be 1.42×10(-4)±6% and 3.08×10(-4)±3% at 25°C, respectively, and increase exponentially with temperature as predicted by the van't Hoff equation. Shower air concentrations for cis- and trans-4-MCHM are predicted to be 0.089 and 0.390ppm-v respectively after 10min, exceeding the US EPA's 0.01ppm-v air screening level during initial spill conditions. Human exposure doses were predicted using measured drinking water and predicted shower air concentrations and found to greatly exceed available guidance levels in the days directly following the spill. Odors would be rapidly detected by 50% of individuals at aqueous concentrations below analytical gas chromatographic detection limits. MMCHC, a minor odorous component (0.935%) of crude MCHM, is also highly volatile and therefore is predicted to contribute to inhalation exposures and odors experienced by consumers.

Tale of two isomers: complexities of human odor perception for cis- and trans-4-methylcyclohexane methanol from the chemical spill in West Virginia.

Application of gas chromatography with mass spectrometric and human olfactory "sniffer" detectors reveals the nature of odorous chemicals from an industrial chemical spill. Crude 4-methylcyclohexane methanol (4-MCHM) spilled in a river and then contaminated drinking water and air for over 300000 consumers living in West Virginia. Olfactory gas chromatography allows investigators to independently measure the odor of chemical components in a mixture. Crude 4-MCHM is comprised of several major cyclohexane components, four of which have distinct isomer pairs. The cis- and trans-4-MCHM isomers are the only components to have distinct odors at the concentrations used in this study. The trans-4-MCHM is the dominant odorant with descriptors of "licorice" and "sweet". Trans-4-MCHM has an air odor threshold concentration of 0.060 ppb-v (95% CI: 0.040-0.091). The odor threshold concentrations are not influenced by gender or age but are lower by a factor of 5 for individuals with prior exposure compared to naïve subjects. Individual trans-4-MCHM odor threshold concentrations vary by more than a factor of 100. The cis-4-MCHM isomer has approximately a 2000-fold higher odor threshold concentration, different descriptors, and an even wider individual response range.

Systematic tracking, visualizing, and interpreting of consumer feedback for drinking water quality.

Consumer feedback and complaints provide utilities with useful data about consumer perceptions of aesthetic water quality in the distribution system. This research provides a systematic approach to interpret consumer complaint water quality data provided by four water utilities that recorded consumer complaints, but did not routinely process the data. The utilities tended to write down a myriad of descriptors that were too numerous or contained a variety of spellings so that electronic "harvesting" was not possible and much manual labor was required to categorize the complaints into majors areas, such as suggested by the Drinking Water Taste and Odor Wheel or existing check-sheets. When the consumer complaint data were categorized and visualized using spider (or radar) and run-time plots, major taste, odor, and appearance patterns emerged that clarified the issue and could provide guidance to the utility on the nature and extent of the problem. A caveat is that while humans readily identify visual issues with the water, such as color, cloudiness, or rust, describing specific tastes and odors in drinking water is acknowledged to be much more difficult for humans to achieve without training. This was demonstrated with two utility groups and a group of consumers identifying the odors of orange, 2-methylisoborneol, and dimethyl trisulfide. All three groups readily and succinctly identified the familiar orange odor. The two utility groups were much more able to identify the musty odor of 2-methylisoborneol, which was likely familiar to them from their work with raw and finished water. Dimethyl trisulfide, a garlic-onion odor associated with sulfur compounds in drinking water, was the least familiar to all three groups, although the laboratory staff did best. These results indicate that utility personnel should be tolerant of consumers who can assuredly say the water is different, but cannot describe the problem. Also, it indicates that a T&O program at a utility would benefit from identification of aesthetic issues in water.

Multicomponent NAPL source dissolution: evaluation of mass-transfer coefficients.

Mass transfer rate coefficients were quantified by employing an inverse modeling technique to high-resolution aqueous phase concentration data observed following an experimental release of a multicomponent nonaqueous phase liquid (NAPL) at a field site. A solute transport model (SEAM3D) was employed to simulate advective-dispersive transport over time coupled to NAPL dissolution. Model calibration was demonstrated by accurately reproducing the observed breakthrough times and peak concentrations at multiple observation points, observed mass discharge at pumping wells, and the reported mass depletions for three soluble NAPL constituents. Vertically variable NAPL mass transfer coefficients were derived for each constituent using an optimized numerical solute transport model, ranging from 0.082 to 2.0 day(-1) across all constituents. Constituent-specific coefficients showed a positive correlation with liquid-phase diffusion coefficients. Application of a time-varying mass transfer coefficient as NAPL mass depleted showed limited sensitivity during which over 80% of the most soluble NAPL constituent dissolved from the source. Long-term simulation results, calibrated to the experimental data and rendered in terms of mass discharge versus source mass depletion, exhibited multistage behavior.